[Dxspider-support] Problem new build 360 With RXCLUS program Logged IN every 6 minutes

[Ian Maude]

I have downloaded this and I am running It in Windows 10 in a VM.  Connected to GB7MBC running build 360.  So far running for 30 minutes with no problems

Ian

> On 23 Nov 2021, at 00:12, Alex via Dxspider-support <dxspider-support at tobit.co.uk> wrote:
> 
> Dirk, 
> the problem is present only for those who use the RXCluster program as I have seen and then asked two other OMs in my area who use RXcluster and connect by me about the problem caused undoubtedly by the space you have removed and that RXCluster does not digest.
> 
> I tried to connect with other programs for example with CC user of ve7cc and also with the logger32 program in telnet towards the dxspider and the connections work perfectly.
> I also tried to connect with RXCluster to node ik4icz-6 which has version 157 build 344 and I remain connected without problems with RXCluster.
> 
> The problem is only with the RXCluster and the latest version 157 build 360 this is confirmed.
> So a little while ago I sent an email to HB9BZA explaining what happens. 
> 
> Let's see what he replies.
> Alex ik5pwj
> 
> -----Messaggio originale-----
> Da: Dxspider-support <dxspider-support-bounces at tobit.co.uk> Per conto di Dirk Koopman via Dxspider-support
> Inviato: martedì 23 novembre 2021 00:51
> A: Alex via Dxspider-support <dxspider-support at tobit.co.uk>
> Cc: Dirk Koopman <djk at tobit.co.uk>
> Oggetto: Re: [Dxspider-support] R: Problem new build 360 With RXCLUS program Logged IN every 6 minutes
> 
> As the website helpfully suggests that I can run the program in Linux under Wine. So I downloaded and installed it. I am happily connected to gb7djk and to you and getting spots. Also, as far as i can tell he is just displaying stuff as I send without messing about with it. Mind you, if I increase the width of the window he does not honour the new set/width command - which a bare telnet session will do.
> 
> So I am a bit confused.
> 
> Dirk
> 
> On 22/11/2021 23:30, Alex via Dxspider-support wrote:
>> Hi Dirk, unfortunately I don't know if it depends on the space you cleared.
>> I don't know how to verify it, but it would seem that whoever uses the 
>> RXCLUSTER program does not receive any dx spot and then after exactly 
>> 6 minutes reconnects again to the cluster that responds to the request 
>> before disconnecting the user, as it is the user always connected, 
>> sending the logged out and then connecting again, send the logged in.
>> 
>> I don't know how it can be solved, but I will try to send an email to 
>> HB9BZA and explain the problem to him to find a solution.
>> 
>>  73 Alex ik5pwj
>> 
>> -----Messaggio originale-----
>> Da: Dxspider-support <dxspider-support-bounces at tobit.co.uk> Per conto 
>> di Dirk Koopman via Dxspider-support
>> Inviato: martedì 23 novembre 2021 00:00
>> A: Alex via Dxspider-support <dxspider-support at tobit.co.uk>
>> Cc: Dirk Koopman <djk at tobit.co.uk>
>> Oggetto: Re: [Dxspider-support] Problem new build 360 With RXCLUS 
>> program Logged IN every 6 minutes
>> 
>> Could this have anything to do with me removing one (useless) space 
>> from the display of spots?
>> 
>> Dirk
>> 
>> On 22/11/2021 21:57, Alex via Dxspider-support wrote:
>>> Unfortunately, since today I upgraded from version 157 build 358 to 
>>> version
>>> 1.57 build 360 I have a problem affecting some connections of users 
>>> who use the RXCLUS 8.5K program.
>>> 
>>> Every 6 minutes the connection from the RXCLUS restarts and then if 
>>> you look at the log, the user first logged OUT and then Logged IN appears.
>>> 
>>>   It seems that in the build 358 version there was a command that 
>>> sent a check to verify the connection and this started from the 
>>> dxspider to the user.
>>>   Now perhaps this does not go with the build 360 version and 
>>> therefore the user who uses the RXCLUS program reconnects after 6 minutes
>>>   even though he is already connected and from the log the logged 
>>> out appears to me first and immediately after the loged IN.
>>> 
>>>   However, I have seen that this only happens with users who use the 
>>> automatic connection with the RXCLUS program.
>>> I also use this program RXCLUS VERSION 8.5K and if I connect to the
>>> ik5pwj-6 cluster with the build 360 installed,
>>>   it happens that every 6 minutes exactly the RXclus program 
>>> automatically resends the connection and then from the log you see 
>>> that the connection is resent ,
>>>   I repeat, this exactly every 6 minutes.
>>> 
>>>   Has anyone noticed anything about it?
>>> 73 Alex ik5pwj.
>>> 
>>> 
>>> 
>>> 
>>> _______________________________________________
>>> Dxspider-support mailing list
>>> Dxspider-support at tobit.co.uk
>>> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
>> 
>> _______________________________________________
>> Dxspider-support mailing list
>> Dxspider-support at tobit.co.uk
>> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
>> 
>> 
>> _______________________________________________
>> Dxspider-support mailing list
>> Dxspider-support at tobit.co.uk
>> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
> 
> 
> _______________________________________________
> Dxspider-support mailing list
> Dxspider-support at tobit.co.uk
> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
> 
> 
> _______________________________________________
> Dxspider-support mailing list
> Dxspider-support at tobit.co.uk
> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support