[Dxspider-support] R: Port 27554 issues
hb9dhg at ticino.com
hb9dhg at ticino.com
Fri Dec 19 10:27:39 GMT 2008
Hello Hans-Juergen,
Hans-Juergen Barthen wrote:
> Hi Marco!
>
> Until today it works stable, no issue anymore.
>
> There is still a localhost entry in the hosts file, but there are usually 2:
>
> ------
> 127.0.0.1 localhost
>
> # special IPv6 addresses
> ::1 localhost ipv6-localhost ipv6-loopback
> ------
>
> netstat showed port 27754 activ on "::1" only, so it was only listening on
> the ipv6-localhost.
> That did not work, I am not using IPv6.
>
> Here my localhost configuration:
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:1503362 errors:0 dropped:0 overruns:0 frame:0
> TX packets:1503362 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:180344849 (171.9 Mb) TX bytes:180344849 (171.9 Mb)
>
> My suggestion is, that IPv6 functionality came in with a new kernel or other
> update and brought up this issue.
You're right. it comes out with the new kernel 2.6 (same is for Fedora
Core 9).
> Now that I changed the $clusteraddr in DXVars.pm from the default value
> "localhost" to it's v4-IP "127.0.0.1" netstat shows port 27754 listening on
> 127.0.0.1 again as usual and everything works fine.
I had the same issue few years ago with CLX, then fixed as you said.
> 73 de Hans, DL5DI
Glad that all is working properly.
Enjoy your cluster
Happy Holidays.
HB9DHG - Fulvio
http://www.hb9dhg.ch
>
>
>> -----Ursprüngliche Nachricht-----
>> Von: dxspider-support-bounces at dxcluster.org
>> [mailto:dxspider-support-bounces at dxcluster.org] Im Auftrag
>> von Marco Zollinger, HB9CAT
>> Gesendet: Freitag, 19. Dezember 2008 08:35
>> An: 'The DXSpider Support list'
>> Betreff: [Dxspider-support] R: Port 27554 issues
>>
>> Hans,
>>
>> still the situation doesn't seem to be stable, if netstat
>> doesn't show any listener or established socket it shouldn't work...
>>
>> Could you check /etc/sysconfig/network/ifcfg-lo to make sure
>> the local loop interface is indeed configured ? it may be
>> corrupted since your crash. Mine (opensuse as well) looks like this:
>>
>> # Loopback (lo) configuration
>> IPADDR=127.0.0.1
>> NETMASK=255.0.0.0
>> NETWORK=127.0.0.0
>> BROADCAST=127.255.255.255
>> STARTMODE=onboot
>> USERCONTROL=no
>>
>> Regarding the discrepancy between 'localhost' and 127.0.0.1
>> this should be only dependent on /etc/hosts (as you state as
>> well), just make sure you still have the
>> 127.0.0.1 localhost
>> line there.
>>
>> Just trying to help an opensuse colleague ;-) using 10.2
>> kernel 2.6.18.2 here
>>
>> Marco, HB9CAT
>>
>
>
> _______________________________________________
> Dxspider-support mailing list
> Dxspider-support at dxcluster.org
> http://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
More information about the Dxspider-support
mailing list