[Dxspider-support] R: Problem new build 360 With RXCLUS program Logged IN every 6 minutes

[Dirk Koopman]

As the website helpfully suggests that I can run the program in Linux 
under Wine. So I downloaded and installed it. I am happily connected to 
gb7djk and to you and getting spots. Also, as far as i can tell he is 
just displaying stuff as I send without messing about with it. Mind you, 
if I increase the width of the window he does not honour the new 
set/width command - which a bare telnet session will do.

So I am a bit confused.

Dirk

On 22/11/2021 23:30, Alex via Dxspider-support wrote:
> Hi Dirk, unfortunately I don't know if it depends on the space you cleared.
> I don't know how to verify it, but it would seem that whoever uses the
> RXCLUSTER program does not receive any dx spot and then after exactly 6
> minutes reconnects again to the cluster that responds to the request before
> disconnecting the user, as it is the user always connected, sending the
> logged out and then connecting again, send the logged in.
>
> I don't know how it can be solved, but I will try to send an email to HB9BZA
> and explain the problem to him to find a solution.
>
>   73 Alex ik5pwj
>
> -----Messaggio originale-----
> Da: Dxspider-support <dxspider-support-bounces at tobit.co.uk> Per conto di
> Dirk Koopman via Dxspider-support
> Inviato: martedì 23 novembre 2021 00:00
> A: Alex via Dxspider-support <dxspider-support at tobit.co.uk>
> Cc: Dirk Koopman <djk at tobit.co.uk>
> Oggetto: Re: [Dxspider-support] Problem new build 360 With RXCLUS program
> Logged IN every 6 minutes
>
> Could this have anything to do with me removing one (useless) space from the
> display of spots?
>
> Dirk
>
> On 22/11/2021 21:57, Alex via Dxspider-support wrote:
>> Unfortunately, since today I upgraded from version 157 build 358 to
>> version
>> 1.57 build 360 I have a problem affecting some connections of users
>> who use the RXCLUS 8.5K program.
>>
>> Every 6 minutes the connection from the RXCLUS restarts and then if
>> you look at the log, the user first logged OUT and then Logged IN appears.
>>
>>    It seems that in the build 358 version there was a command that sent
>> a check to verify the connection and this started from the dxspider to
>> the user.
>>    Now perhaps this does not go with the build 360 version and
>> therefore the user who uses the RXCLUS program reconnects after 6 minutes
>>    even though he is already connected and from the log the logged out
>> appears to me first and immediately after the loged IN.
>>
>>    However, I have seen that this only happens with users who use the
>> automatic connection with the RXCLUS program.
>> I also use this program RXCLUS VERSION 8.5K and if I connect to the
>> ik5pwj-6 cluster with the build 360 installed,
>>    it happens that every 6 minutes exactly the RXclus program
>> automatically resends the connection and then from the log you see
>> that the connection is resent ,
>>    I repeat, this exactly every 6 minutes.
>>
>>    Has anyone noticed anything about it?
>> 73 Alex ik5pwj.
>>
>>
>>
>>
>> _______________________________________________
>> Dxspider-support mailing list
>> Dxspider-support at tobit.co.uk
>> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
>
> _______________________________________________
> Dxspider-support mailing list
> Dxspider-support at tobit.co.uk
> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support
>
>
> _______________________________________________
> Dxspider-support mailing list
> Dxspider-support at tobit.co.uk
> https://mailman.tobit.co.uk/mailman/listinfo/dxspider-support